Ajantha College and School Students Science Projects materials The Great in project

"In the name of Allah, most
Gracious, most Compassionate"

Phone

044 4213 1795

Mobile

+91 91764 16648
 

MAGNETOPOT SENSORS

Prominent & Leading Supplier and Trader from Mumbai, we offer MAGNETOPOT SENSORS such as Proximity Sensors MagnetoPot 50mm, Sensor MagnetoPot 10K OHM 25MM and Proximity Sensors MagnetoPot 100mm.

MAGNETOPOT SENSORS

Proximity Sensors MagnetoPot 50mm

proximity-sensors-magnetopot-50mm-250x250
  • Contactless Linear Sensor
  • IP64 debris proof. splash proof
  • Ideal for hydraullic and Pnematic position Sensing
  • Liquid Level Capability
  • -Upon request
  • Male or Female Nicomatic connectors
  • Corresponing exterior magnet
  • Life cycle> 1 million
  • height <=3.50 mm
  • Actuation Force: 0.09 to 0.11 lbs pull force at desired distance
  • Resistance Standard : 10 K ohms
  • Resistance Custom: 5 K to 500 k ohms
  • Effective Electrical Travel: 8 to 1200 mm
  • Resolution : Depends on the exterior magnet strength and distance to the magnetopot
  • Power Rating: 0.50 watt continuous
  • Di electric value: No affect @500 VAC for 1 minute

The MagnetoPot is simple, yet elegant in its ability to track motion in a contactless manner. A magnet on the inside of a cylinder, or a magnet on the opposing side of a motion device will guide the built-in magnetics of the MagnetoPot for position location through a potentiometric output.The MagnetoPot is a sealed potentiometer, in the membrane potentiometer tradition, yet it does not require a wiper/actuator to connect the collector and the resistor. Instead, the MagnetoPot is controlled by an outside magnet, which attracts the magnetic forces within the MagnetoPot to connect to the linear resistor and give linear potentiometer feedback.The wiper inside the sealed pot is magnetic or ferromagnetic, and will only perform if connected with an exterior magnet. As opposed to a magnetically-based Reed Switch, which gives simply “open” or “close” signals, the MagnetoPot gives the full linear travel of a hydraulic or pneumatic cylinder. In liquid level applications, the MagnetoPot can attach to the outside of a liquid tank and give position of the magnet inside the float. No water ingress, no wearing of the part by environment, because the MagnetoPot is outside of the tank.

The MagnetoPot is made of polyester, fiberglass and kapton, depending on the specification required. It functions as a voltage divider, a resistor or rheostat, as desired by the end-user. By bringing the exterior magnet into a proximity necessary to connect with the internal magnetic attractors, the operator can obtain linear position sensing based on the location of the exterior magnet. As the exterior magnet moves, so does the electrical output of the MagnetoPot.The MagnetoPot should not be mounted to a ferromagnetic surface.

Sensor MagnetoPot 10K OHM 25MM

industrial-motion-position-sensors-hotpot-1000mm-250x250

Contactless Linear Sensor

  • IP64 Debris Proof, Splash Proof,
  • Ideal for hydraullic and pneumatic Position sensing
  • Liquid level capability
  • Upon request
  • - Male or Female Nicomatic Connectors
  • -Corresponding Exterior Magnet
  • Life Cycle > 1 million
  • Height < =3.50 mm
  • Resistance: 10 K ohms Standadrd
  • Effective electrical travel: 8 to 1200 mm
  • power rating: 0.5 watt
  • Resolution: Depends on the exterior magnet strength and distance to the magnetopot
  • Di electric value: No affect @500 VAC for 1 minute

The MagnetoPot is simple, yet elegant in its ability to track motion in a contactless manner. A magnet on the inside of a cylinder, or a magnet on the opposing side of a motion device will guide the built-in magnetics of the MagnetoPot for position location through a potentiometric output.The MagnetoPot is a sealed potentiometer, in the membrane potentiometer tradition, yet it does not require a wiper/actuator to connect the collector and the resistor. Instead, the MagnetoPot is controlled by an outside magnet, which attracts the magnetic forces within the MagnetoPot to connect to the linear resistor and give linear potentiometer feedback.

The wiper inside the sealed pot is magnetic or ferromagnetic, and will only perform if connected with an exterior magnet. As opposed to a magnetically-based Reed Switch, which gives simply “open” or “close” signals, the MagnetoPot gives the full linear travel of a hydraulic or pneumatic cylinder. In liquid level applications, the MagnetoPot can attach to the outside of a liquid tank and give position of the magnet inside the float. No water ingress, no wearing of the part by environment, because the MagnetoPot is outside of the tank.

Proximity Sensors MagnetoPot 100mm

proximity-sensors-magnetopot-100mm-250x250

Contactless Linear Sensor

  • IP64 Debris proof, Splash Proof.
  • Ideal for Hydraullic and Pneumatic position sensing
  • Liquid level capability
  • Upon request
  • - male or female nicomatic connectors
  • - corresponding exterior magnet
  • Life Cycle> 1 million
  • Height<=3.50 mm
  • Actual force: 0.09 to 0.11 lbs pull force at desired distance
  • Resistance Standards: 10 K ohms
  • Resistance Custom; 5 K to 500 k ohms
  • Effective electrical travel: 8 to 1200 mm
  • Resolution: Depend on the exterior magnetic strength and distance to the magnetopot
  • Power Rating: 0.50 watt continuous
  • Dielectric value: no affect @500 VAC for 1 minute continuous

How it works:

The MagnetoPot is simple, yet elegant in its ability to track motion in a contactless manner. A magnet on the inside of a cylinder, or a magnet on the opposing side of a motion device will guide the built-in magnetics of the MagnetoPot for position location through a potentiometric output.The MagnetoPot is a sealed potentiometer, in the membrane potentiometer tradition, yet it does not require a wiper/actuator to connect the collector and the resistor. Instead, the MagnetoPot is controlled by an outside magnet, which attracts the magnetic forces within the MagnetoPot to connect to the linear resistor and give linear potentiometer feedback.The wiper inside the sealed pot is magnetic or ferromagnetic, and will only perform if connected with an exterior magnet. As opposed to a magnetically-based Reed Switch, which gives simply “open” or “close” signals, the MagnetoPot gives the full linear travel of a hydraulic or pneumatic cylinder. In liquid level applications, the MagnetoPot can attach to the outside of a liquid tank and give position of the magnet inside the float. No water ingress, no wearing of the part by environment, because the MagnetoPot is outside of the tank.